-
Toutes les catégories
-
Mouvements d'horloges
-
DUGENA Quarz-Uhrwerke
-
Mouvements radio pilotée
-
Mouvements à quartz
-
Mouvements de montres
-
Mécanisme enfichable
-
Mouvement à ressorts
-
Mouvement de pendule à quartz
-
Mouvements à chaînes
-
L'aperçu des couples d'aiguille
-
Couple d'aiguilles
-
Cadrans et givres de chiffre
-
Ressort de suspension
-
Kieninger movement-kits
-
Ressort de pendule
-
Chaîne d'horloge
-
Equipement et accessoires
-
Mécanisme pour balancier tournant
-
Ornaments en bois
-
Mouvements à chaînes
-
Petites pièces
-
Chaînes des horloges
-
Accessoires de montre
-
Ersatzteile für Rolex
-
Mouvement de coucou
-
Mouvement á ressort
-
Ornament en métal
-
Mouvements de musique
-
Mouvement à quartz avec coup
-
Pendules pour horloges
-
Mouvements à câbles
-
Aiguille de seconde
-
Mouvements de pendule de parquet
-
Mouvements synchrones
-
Aiguilles pour montre de poche
-
Pancarte d'horloges
-
Jeux de chiffres
-
Ressorts de traction
-
DUGENA Quarz-Uhrwerke
-
Outil d'horloger et besoin d'atelier
-
Horloges et montre-bracelets
-
Fabrication et conception
-
Instruments optiques
-
Technologie d'alarme et de sécurité
-
Instruments météorologiques
-
Connaissance de spécialiste et littérature
-
Bijoux
-
Verres d'horloge
-
Idée de cadeau
-
GRS Gravieren
-
Nouveautés
-
3D
-
Selva Fachtipps
-
Manufakturwerk
-
Mouvements d'horloges
Réf. produit :
334735
Informations sur le produit "Clés pour grandes horloges Modèle standard acier tige longue Intérieur carré : 3,75"
Pour les horloges de table, les horloges murales et les horloges sur pied.
INFO
Les dimensions classiques des clés n° 00 à 15 ne sont connues que de l'horloger.
Les dimensions selon lesquelles les clés de remontoir sont également définies se réfèrent au carré de remontoir du mouvement. On mesure donc le carré de remontoir (avec un pied à coulisse !), on arrondit le résultat à 0,25 mm et on choisit ensuite la clé. La clé est livrée exactement adaptée avec la bonne tolérance positive (mesure théorique plus environ 0,1 mm).
Pour les montres plus anciennes dont le carré de remontage est conique, la mesure ne se fait pas à l'extrémité avant, "fine", mais un peu plus bas, vers l'extrémité intérieure du carré. Le résultat de la mesure est arrondi à 0,25 mm et la clé est ensuite sélectionnée.
Si un carré n'est pas exactement carré, mais présente un écart rectangulaire en coupe, déterminer la mesure de la plus grande longueur d'arête.
Les carrés de remontoir abîmés sont souvent limés lors d'une réparation. Lors de cette opération, ou si un ressort de traction a été remplacé par un ressort trop fort, la clé de remontoir peut être soumise à des contraintes exceptionnelles qui peuvent l'endommager, voire la faire éclater. Il en va de même lorsqu'une clé a été choisie trop grande ou que les arêtes longitudinales du carré de remontage sont usées et arrondies. Dans de tels cas, la garantie, qui se limite au remplacement de la clé, est exclue.
Remarque : lorsque vous mesurez le trou carré d'une clé, ne mesurez pas sur le centre du trou, mais entre deux coins opposés. La raison en est que la section du trou n'est pas purement carrée, mais qu'il s'agit d'un trou rond qui a été repercé avec un "mandrin de brochage". Comme le diamètre de l'alésage est légèrement plus grand que la "largeur de clé" proprement dite, la mesure effectuée à l'envers donne une cote carrée trop grande.
INFO
Les dimensions classiques des clés n° 00 à 15 ne sont connues que de l'horloger.
Les dimensions selon lesquelles les clés de remontoir sont également définies se réfèrent au carré de remontoir du mouvement. On mesure donc le carré de remontoir (avec un pied à coulisse !), on arrondit le résultat à 0,25 mm et on choisit ensuite la clé. La clé est livrée exactement adaptée avec la bonne tolérance positive (mesure théorique plus environ 0,1 mm).
Pour les montres plus anciennes dont le carré de remontage est conique, la mesure ne se fait pas à l'extrémité avant, "fine", mais un peu plus bas, vers l'extrémité intérieure du carré. Le résultat de la mesure est arrondi à 0,25 mm et la clé est ensuite sélectionnée.
Si un carré n'est pas exactement carré, mais présente un écart rectangulaire en coupe, déterminer la mesure de la plus grande longueur d'arête.
Les carrés de remontoir abîmés sont souvent limés lors d'une réparation. Lors de cette opération, ou si un ressort de traction a été remplacé par un ressort trop fort, la clé de remontoir peut être soumise à des contraintes exceptionnelles qui peuvent l'endommager, voire la faire éclater. Il en va de même lorsqu'une clé a été choisie trop grande ou que les arêtes longitudinales du carré de remontage sont usées et arrondies. Dans de tels cas, la garantie, qui se limite au remplacement de la clé, est exclue.
Remarque : lorsque vous mesurez le trou carré d'une clé, ne mesurez pas sur le centre du trou, mais entre deux coins opposés. La raison en est que la section du trou n'est pas purement carrée, mais qu'il s'agit d'un trou rond qui a été repercé avec un "mandrin de brochage". Comme le diamètre de l'alésage est légèrement plus grand que la "largeur de clé" proprement dite, la mesure effectuée à l'envers donne une cote carrée trop grande.
Application: | 3,75 |
---|---|
Dimensions intérieures Ø mm: | 3.75 |
Désignation du fabricant: | 6 |
Matériau: | Messing, verchromt |
Nom de l'article: | Großuhrschlüssel |
Particularité: | langer Schaft |
Type de transformation: | verchromt |